Original Replacement Controller unit for  Yaesu G450CDC

Mini Din Plug

Chassis Part to hold Antenna and Encoder

Used for: Uniden UBCD3600XLT

Keypad

Use for: Uniden EZI33XLT and EZI33XLT+.

Plastic Fixing Ring

Used for: Sirio Starduster M-400.

Brass Radial Reinforce

Use  for:Sirio S827 and Blizzard

DC Power Cord with Fuse Holder
• Fuse: 10 Ampere
• Length: 200 cm
• Packing: Bulk

Use for: CRT MICRON and others

Keypad 3 buttons under LCD for Uniden SDS200E.

Keypad for Uniden SDS200E.

Keypad for Uniden UBCD3600XLT.

Desktop Charging Cradle
• Charger/Adaptor is not included

Use for: Midland G10, G10 Mossy Oak.

Keypad used in Uniden UBC75XLT.

Hardware Bag, Replacement Parts for W1000/W5000 CB Antenna.
• Weather Cap.
• Hex Key.
• Connector Adaptor UHF-Male/FME-Male.

Use for: Wilson Types W1000 MagMount, W1000 TrunkLip, W1000 RoofTop, W5000 MagMount, W5000 TrunkLip, W5000 RoofTop

Roof Top Mount Repair Kit for W1000/W5000 Series Roof Top Mount.
Includes: Mast, Set Screws, Panel Nut, Rubber Coil Washer, Stand Off, Roof Gasket.

Use for: Wilson Types Wilson 1000 Roof Mount, Wilson 5000 Roof Mount .

Hardware Bag, Replacement Parts for Wilson W5000 Series CB Antennas.
• Weather Cap.
• Hex Key.
• Connector Adaptor UHF-Male.

Use for: Wilson Types W5000 MagMount, W5000 TrunkLip, W5000 RoofTop

RG58 Coax Cable and Mount Assembly for W1000 Series Roof Top Mount
Connector at Coax is  FME-Female

Use for: Wilson Types W1000 RoofTop, W5000 RoofTop.

Repair Kit for W500 Series Magnet Mount CB Antenna.
Includes: Mast, Set Screws, Mylar Set, Hex Key, Rubber Whip Tip.

Use for: : Wilson-500 Magnet Mount Antenna.

Trunk Mount Antenna Repair Kit for W1000/W5000 Trunk Mount Series.
Includes: Mast, Set Screws, Panel Nut, Rubber Coil Washer, Stand Off, Trunk Gasket.

Use for: Wilson Types W1000 Trunk Mount, W5000 Trunk Mount.

Roof Mount Gasket for W1000/W5000.

Use for: Wilson Types Wilson 1000, Wilson 5000.

Plastic Stand off for W1000 and W5000 Series.

Use for: Wilson Types Wilson 1000, Wilson 5000.

Keypad used in Uniden UBC125XLT.

Fan + Plastic Guard/Protection 
• Dimensions Fan 80x80x20 mm
• Total dimensions 80x80x25 mm
• Voltage 12 Volt, 1.56 Watt
• Sleave Bearing.

Use for: RM VLA200-V.

Rubber for Stand of Uniden-Bearcat Model UBC9000XLT

Stand is GCMZ428673Z.
Holder for this stand is GCMZ428672Z.

Road Case Electrical Panel, including Cables.

Used for: K40 Road Cases RCPLUSPNL, RCPLUS Plug&Play.

Stand for Uniden-Bearcat Model UBC9000XLT

Rubber for this stand is LFUT428690Z.
Holder for this stand is GCMZ428672Z.

HOLDER for Stand of Uniden-Bearcat Model UBC9000XLT

Stand is GCMZ428673Z.
Rubber for stand is LFUT428690Z.

Bottom Part of Antenna DX-HT701

Adaptor 3/8x24-Male to Whip-Female.
•  Allows to use a regular metal whip on a 3/8x24 thread stud.
• Whip diameter max 3 mm

BUZZER, 2-Pin.

Used in: Danita APA100.

Earpiece Transparent

Use for: MA31-L, MA31-LK and others.

Eva Box.

Use for: HP450

Holster with Rotating 180 degrees Belt Clip.

Use for: Use for:  HP450 and others.

Nitro-Knob, Lighted Radio Knob Kit with Triple LED Illumination.
* Volume/Squelch Control Knob
* Blue LEDs - Knob Glows Blue
* Extra Long Knob - Easier to Reach
* For D Shaft Controls

Use for: Magnum S9 and others.
To change all knobs of S9 into Nitro Knobs you need 5 pcs NK1 , 2 pcs NK2 , 1 pc NK3.

Nitro-Knob, Lighted Radio Knob Kit with Triple LED Illumination.
* Band / Rotary Control Knob
* Blue LEDs - Knob Glows Blue
* Extra Long Knob - Easier to Reach
* For Knurled (18 Teeth) Shaft Controls

Use for Magnum S9 and others.
To change all knobs of S9 into Nitro Knobs you need 5 pcs NK1, 2 pcs NK2, 1 pc NK3.

Nitro-Knob, Lighted Radio Knob Kit with Triple LED Illumination.
* Channel/Frequency Control Knob
* Blue LEDs - Knob Glows Blue
* Extra Long Knob - Easier to Reach
* For D Shaft Controls

Use for:  Magnum S9 and others.
To change all knobs of S9 into Nitro Knobs you need 5 pcs NK1, 2 pcs NK2, 1 pc NK3.

Fan, 12 Volt, 1.6 Watt.
Dimensions 40 x 40 x 20 mm.

Fan, 12 Volt, 1.1 Watt, Sleeve Bearing.
Dimensions 60 x 60 x 25 mm.

Fan, 24 Volt, 0.18 Ampere, Sleeve Bearing.
Dimensions 60 x 60 x 25 mm.

Fan, 24 Volt, 2.0 Watt, Ball Bearing.
Dimensions 60 x 60 x 25 mm.

Fan, 24 Volt, 0.25 Ampere, Sleeve Bearing.
Dimensions 120 x 120 x 25 mm.

Fan, 24 Volt, 6.7 Watt, Sleeve Bearing.
Dimensions 120 x 120 x 38 mm.

Rubber for PTT of UBZ-LF68.

Crimp Terminal, Standard 0.062 inch, 1.57 mm Diameter, Pin and Socket Crimp Terminal, Series 1560, Male, with Tin (Sn) Plated Brass Contact, 18-24 AWG.

On Rear Panel of President Lincoln is a 9-Pins Accessory Connector. These are the Pins to use with this Connector. Read the User Manual how to (de-)activate Functions like External Speaker, Internal Speaker, PA-Speaker and Morse Key by using the Pins on designated position and use Shortening Wires.

Name Plate for MVT7100

1 Set of 5 Pcs of Battery Clips.
Used in Yupiteru MVT7100

Replacement Quick Disconnect Acoustic Clear Tube, Clear Eartip.

Use for: KHS8BL

Coax Connector UHF-Female (SO-239), for Sirio SD27

Ring + Screw used for Solarcon GPK1.

Ceramic Insulator, TO-220.

Carrying Strap / Wrist Strap, Black, Total Length 23 cm.

Use for: JMC Type RTP1000,Uniden-Bearcat Types UBC75XLT, UBC125XLT, UBC3500XLT, USC230 and all other brands/types with a hole to connect a wrist strap.