Scanners and Receivers

Low Noise Wide Band GaAs FET Pre-Amplifier 24MHz - 2150MHz.
Antenna Connection: BNC-Female.
Receiver Connection: BNC-Male.

Pre-Amplifier for Wideband Receiving
• Frequency Range: 0,5 - 1500 MHz
• Gain: adjustable  20 dB MAX - 20 dB MIN
• Permitted power: 
• Connectors: 2 Pcs of UHF-Female 
• DC-Input Connection: 
• Operating Voltage: 13,8 Volt
• Packing: Box

ARL2300 Ethernet Controller enables remote control and audio streaming for AOR receivers via LAN/internet.
• Compatible with AR2300, AR2300/IQ, AR5001D, AR5700D, AR6000.
• LAN: RJ-45, 10/100Mbps
• Audio Input: 3.5 mm stereo (mono)
• Power Input: 5 VDC
• Protocols: TCP (control), UDP (audio)

BATTERY PACK 
• Type: Li-Ion
• Voltage: 3,6 Volt
• Capacity: 3120 mAh 
•  Color: Blacj

Use for: Alinco DJ-X100(E).

Dry Cell Battery Case (Battery Holder)
• For 3 Pcs AA Cell

• Use for: Alinco DJ-X100.(Japan) , Alinco DJ-X100E (europe)  Alinco DJ-X100T (USA)

Professionally designed lapel speaker 
• Great for use with Scanner or Portable Transceivers.
• Speaker: Amplified speaker 
• Power: USB-C charging
• Power: On/off power button with LED on top of speaker mic reduces battery drain 
• Connection: 3.5 mm connection 
• Clip: Swivel clip allows you to clip on multiple ways to your shirt or jacket
• Packing: Box-1

External Speaker, Impedance 4 Ohm, Power Continuous 10 Watts and Max 20 Watts.
Dimensions 12,7 x 12,7 x 9 cm, Color CHROME.
Cable 300 cm with 3,5 mm Mono Plug.
Heavy Duty Model.

Clip for Uniden UBC30XLT, EZI33XLT.

Replacement Earphone 3.5 mm for Uniden EZI33XLT.

Switching Power Supply, EU/UK connector
◾ Input Connector: AC-EU 2-Pin / UK 3-Pin
◾ Input Data: AC 100 - 240 Volt, 50/60 Hz, 300 mA
◾ Output Connector: USB Slot
◾ Output Data: DC 5 Volt, 2000 mA

Original Repacement, use for Uniden SDS100E.

BATTERY PACK including COVER and CUSHION
• Type: Li-Ion
• Voltage: 3,7 Volt
• Capacity: 3600 mAh (13,2 Wh)

Use for:  Uniden SDS100E

Battery Pack
• Type: Li-Ion
• Voltage: 3,7 Volt
• Capacity: 5400 mAh (19,98 Wh)

Use for:  Uniden SDS100E

Nylon Carry Case

Use for: Uniden SDS100E

Soft Leather Carry Case.

Use for: Uniden SDS100E.

GPS Adapter Cable.
• Allows to connect the BC-GPSK to your BCD325P2 or SDS100(E) scanner's USB port for Location-based Scanning control

Use for:  Uniden BC-GPSK to connect to Uniden SDS100 or SDS100E.

BATTERY PACK 
• Type: Li-Ion
• Voltage: 3,7 Volt
• Capacity: 3600 mAh (13,2 Wh)

Use for Uniden SDS100E

GPS Receiver for Scanner Uniden SDS200 and SDS200E.

Switching Adapter GQ15-138060-AX
◾ Original Replacement Power Suply
◾ Input Connector: AC-EU 2-Pin, AC-UK 3-Pin, AC? 2-Pin
◾ Input Data: AC 100-240 Volt, 50/60 Hz, Max  500 mA.
◾ Output Connector: In +/-4 mm, Out +/-6 mm, Length +/-9 mm.
◾ Output Data: DC 13,8 Volt, 600 mA.

Powersupply for Whistler TRX-2.

Programming Cable

Used for: Uniden SDS200E.

SPS, Switching Power Supply, AD-1287, EU/UK Switch over Plug.
◾ Input Connector: AC-EU 2-Pin plus AC-UK 3-Pin.
◾ Input Data: AC 100-240 Volt, 50/60 Hz, 600 mA.
◾ Output Connector: In 2.1 mm, Out 5.5 mm, Length 9.5 mm.
◾ Output Data: DC 13.8 Volt, 700 mA.

Original Repacement, use for Uniden SDS200E , BCT15X .

High Quality Leather Carry Case

Use for: Whistler TRX-1.

HOLDER for Stand of Uniden-Bearcat Model UBC9000XLT

Stand is GCMZ428673Z.
Rubber for stand is LFUT428690Z.

External Speaker, 5 Watts, 8 Ohm, with Switchable Noise Filter and 8 dB Attenuator, Cable Length 2 Meter with 3.5mm Mono Plug.
Packing Blister-1.

 

External Speaker, 5 Watts, 8 Ohm.
Cable with 3.5mm Mono Plug.
Packing Blister-1.